573 WARNING: Cancer and Reproductive Harm- www.P65Warnings.ca.gov Fuel & Exhaust SECTION SECTION LL Camaro Camaro Parts and Accessories Parts and Accessories Exhaust Components Exhaust Components Universal Balance Pipe Set Flowmaster offers a pre-fabricated universal balance pipe set to ease the installation of a crossover pipe in a dual exhaust system. Set includes: T-pipe connectors, balance pipe, and clamps. F15920 2-1/2" ................................... set Exhaust Components P1065 F15920 BWP052 10778 Tru-X and Y-Pipes The more gentle radius of these X- and Y-pipes allow for better exhaust gas scavenging, noise cancellation and better balance between cylinder banks. The result is a significant increase in power and torque, but a reduction in dB sound levels. X-Pipe 10781 2-1/2" dual in/out x 9.5" long ea 10782 3" dual in/out x 13.2" long ..... ea Crossover 10790 2-1/4" dual in/out x 12" long .. ea 10791 2-1/2" dual in/out x 12" long .. ea 10792 3" dual x in/out x 14" long ..... ea Y-Pipe 10748 2-1/2" single, 2" dual.............. ea 10758 2-1/2" single, 2-1/4 dual ......... ea 10768 2-1/2" single, 2-1/2 dual ......... ea 10778 3" single, 2-1/2 dual ............... ea 10798 3" pipe, 3" dual ....................... ea 10792 1967-81 X-Crossover Dump Legs Pypes dump legs are made to replace the front legs of the X-pipe crossover on 1967-81 Camaro models, making installation of electric exhaust cutouts simpler. Each dump leg is strategically located for maximum ground clearance and includes block-off plates and hardware, and is manufactured from 409 stainless steel with mandrel bends to allow maximum exhaust flow. Add the optional electric exhaust cutouts and make uncorking your exhaust as easy as flipping a switch, sold separately. Made in USA. P1077 1967-81 2-1/2" ................. set P1078 1967-81 3" ........................ set 1967-81 Tunnel X-Crossover Since a V8 fires alternately, exhaust exits in pulses rather than a steady flow. While one pipe is filled with pressure the other pipe is relatively pressureless, but connecting the two pipes in a Siamese pattern allows pressure to be equalized between the two tailpipes. This action allows the exhaust to pass through quicker for better breathing that increases horsepower. All crossovers are made of 409 stainless steel with dual reinforcement plates at the welds where they are needed most. All pipes are mandrel bent to allow for the maximum flow of exhaust gasses, which boosts acceleration. Limited lifetime warranty. Important: If using stock, cast iron manifolds, add a set of down pipes to connect your original manifolds to the header back system. Note: Shipped oversize. 2-1/2" Tunnel Crossover P1065 1967-81 .................................. ea 3" Tunnel Crossover P1067 1967-81 .................................. ea 1967-74 SB Exhaust Manifold Front Pipes Magnaflow has designed these manifold pipes to fit OEM exhaust manifolds and allow for the installation of a performance exhaust system. Manufactured from corrosion resistant stainless steel to ensure longevity featuring 2-1/2" tubing and a 3 bolt flange connection. Note: Shipped oversize. 16434 1967-74 small block .......... set P1078 3" Crossover X-Pipe X-Change X-pipes allow you to open and close your exhaust with the bolting or unbolting of dump plates. Crossover includes dual stainless reinforcement plates at the welds where they are needed most. All pipes are mandrel bent, to allow for the maximum flow of exhaust gasses, which boosts acceleration. Fabricated using the highest quality materials, smooth, seam coated, mandrel bent, stainless steel pipe resists corrosion and extends the life of your system. P1094 polished stainless steel ........... set 1967-81 Manifold Down Pipes Not all performance enthusiasts use collector style headers, so Pypes has designed 2-1/2" down pipes for log style, rear exit exhaust manifolds to fit your Pypes header back systems. These down pipes are made from 409 stainless steel and mandrel bent 16 gauge tube that fit directly onto factory cast iron manifolds, and slip into the header back systems. Manifold flanges are already installed. Note: Shipped double oversize. Emissions Note: * Non-CARB compliant (not legal for emission controlled vehicles). Small Block P1006 1967-77 2-1/2", 3 bolt ..... pr P1058* 1978-81 2-1/2", 2 bolt ..... pr Big Block P1011 1967-81 2-1/2", 3 bolt ...... pr P1011 1967-68 OE Style Exhaust Tailpipes These original style tailpipes features the correct factory styled flat areas, bends and outlet. Manufactured to factory specifications from aluminized tubing. Correct for SB or BB applications. EX80045 1967-68 all ....................... pr 1967-69 3" Camaro Tailpipe Set Flowmaster’s 3" mandrel bent tailpipe set covers 1967- 69 Camaro models. This tailpipe set is designed so you can create a mandrel bent custom high-performance exhaust for any Camaro including convertibles. Designed to exit between the tires and rear bumper on either side of the vehicle. Note: Hardware and hangers are not included. F15822 1967-69 ................................ set 43989 1967-87 Aluminized Tailpipe OEM style tailpipes which are aluminized offering a superior appearance to the coated style originals. Long-lasting and effective against salt road winters. Note: *With dual chrome tips. Intermediate Pipes 43745 1977-81 LH ......................... ea 43744 1977-81 RH ........................ ea Tailpipes – Dual Exhaust E254 1967-68 LH ......................... ea E253 1967-68 RH ........................ ea E258 1969 LH and RH ........... pr 43831 1982-87 LH, 305H 4bbl ...... ea 43846 1982-87 RH, 305H 4bbl ..... ea 43989 1984-86 LH, 305G,F 4bbl .. ea 43988 1984-86 RH, 305G,F 4bbl .. ea Stainless Steel Exhaust X-Pipe Black Widow Exhaust X-pipes are mandrel bent out of stainless steel. Designed for maximum performance and sound, Black Widow’s X-pipes balance exhaust flow and sound and promote scavenging. BWP052 2-1/2" ................................. ea BWP053 3" ........................................ ea
